Lighting Installation in Kennedale

Better light, wired the right way

Good lighting changes how a room works. A kitchen with lights under the cabinets is safer to cook in. A hallway with a switch at both ends means no more walking in the dark. A ceiling fan that doesn't wobble keeps a bedroom comfortable through a long Texas summer.

What you don't see matters just as much. Every new light needs a box rated for its weight, a circuit with room for the load, and connections that stay tight for years. We look at all of that before we cut a hole, so the light you pick is the light that ends up working well.

We treat your home the way we'd want a neighbor to treat ours. That means drop cloths down, careful cuts in drywall, and a straight answer if an idea won't work as planned.

Lighting work we handle

Recessed and wafer lights

We lay out recessed lights so they light the room evenly instead of making spots and shadows. In ceilings below an attic, we use fixtures rated for contact with insulation, which matters when attic temperatures climb in summer.

Fixture swaps and chandeliers

Replacing an old fixture sounds simple, but heavy chandeliers and pendants need a box and mounting that can carry them. We check the box, the wiring and the ground before hanging anything new.

Ceiling fans

A fan needs a fan-rated box braced to the framing, not a standard light box. We install that support, balance the blades and set up the wall control or remote.

Dimmers and smart switches

Many LED bulbs flicker or buzz on older dimmers. We match the dimmer to the bulbs so the lights fade smoothly, and we wire smart switches that need a neutral the right way.

Under-cabinet and accent lighting

We run low-profile lighting under kitchen cabinets and along shelves, with the driver hidden and the switch where you'll actually reach for it.

Outdoor and security lighting

Porch lights, flood lights, landscape lighting and motion sensors, all with weather-rated fittings and protected outdoor connections. Photocells and timers can handle the on and off for you.

Signs it's time for new lighting or a closer look

• Rooms that stay dim

  If you're using lamps in the middle of the day or squinting at the stove, the room likely needs more light or better placement.

• Flickering or buzzing

  Flicker after a bulb change usually points to a dimmer mismatch. Flicker with standard switches can mean a loose connection, which we'd want to find before adding anything new.

• Fixtures that run hot

  Discolored trim, a burnt smell or brittle wires at an old fixture are signs of heat damage. That is worth fixing even if the light still turns on.

• A wobbling ceiling fan

  Constant wobble often means the fan is hanging from a box that was never meant to hold it.

• A dark yard or driveway

  If you come home to a dark walkway, outdoor lighting with a motion sensor or timer makes the trip from car to door safer.

How a lighting job goes

1. 1

   We talk it through on the phone

   You tell us what you want to light and what's bothering you about the current setup. We set a time for a service visit that fits your schedule.

2. 2

   We look before we plan

   At your home we check the circuit, the attic or crawl access, and the boxes in place. Then we explain what's involved and give you the cost in writing before any work starts.

3. 3

   We protect the space and do the work

   Floors and furniture get covered. We cut only what's needed, run the wiring, mount the supports and install the fixtures. When the job calls for paperwork with the city, we file it ourselves and meet the inspector, so you aren't stuck sorting that out.

4. 4

   We test and tidy up

   Every light, switch and dimmer gets tested with you there. We patch our openings so they're ready for paint, clean up the dust and walk you through any new controls.

What affects the cost of lighting installation

Two jobs that look the same on paper can be quite different once we see the ceiling. We price each one after the visit, line by line, so you know what you're paying for before we begin.

Number and type of fixtures

Six recessed lights take more time than one fixture swap. Heavy chandeliers and fans need extra bracing.

Access to the ceiling

An open attic above makes running wire straightforward. A second-floor ceiling or a vaulted room means more careful fishing and sometimes more patching.

New circuits or switches

Lights on an existing switch cost less than lights that need a new circuit, a new switch location or three-way switching.

Condition of existing wiring

If we find damaged wires, missing grounds or overloaded circuits, we'll show you and explain the fix. Bigger issues may fall under our electrical repair work.

Outdoor runs

Exterior lighting may need weather-rated boxes, trenching or longer wire runs, which add time and material.