ServicesCode Corrections & Inspection Fixes
Code Corrections & Inspection Fixes in Kennedale
Got a correction notice from the city or a home inspection report full of electrical items? We go through the list with you, fix each item the right way, and explain what was wrong in plain words so you know your home is safe.
Turning a Report Full of Red Flags Into a Finished List
An inspection report can feel worse than it is. Many electrical write-ups are small fixes: a missing cover plate, an outlet that needs GFCI protection, two wires sharing a breaker built for one. A few point to real hazards that need attention before anyone moves in or closes a wall.
We read the report the way a neighbor would, sorting what's urgent from what's minor. Then we fix the items listed and nothing you didn't ask for. If we spot something serious that isn't on the report, we show you a photo and let you decide.
This work comes up most often during a home sale, after a permit inspection on a remodel, or when you've found wiring a previous owner did themselves.
What a Correction Visit Covers
- A walk through your report
- We go line by line through the inspector's notes with you. Each item gets a plain explanation and a clear fix.
- GFCI and AFCI protection
- Kitchens, bathrooms, garages, laundry areas and outdoor outlets often need ground-fault protection to meet current code. We add it at the outlet or the breaker, whichever fits your home better.
- Panel write-ups
- Double-tapped breakers, missing knockout fillers, wrong-size breakers and incomplete labeling are common panel findings. We correct them and label circuits so the next person can read your panel.
- Open boxes and loose splices
- Wire nuts hanging in an attic or a splice with no box are fire risks. We put connections inside proper covered boxes.
- Grounding and bonding
- Three-prong outlets on ungrounded wiring and missing bonding at water or gas lines show up often. We fix them in a way that meets code rather than just hiding the problem.
- Outdoor and exterior items
- Exterior outlets without weather-rated in-use covers and damaged conduit get replaced with parts made to sit outside year-round.
Signs It's Time to Call for Code Corrections
A buyer's inspection flagged electrical items
Repair requests during a sale usually come with a deadline. We help you get the electrical items done properly so the deal can keep moving.
Your permit inspection didn't pass
A failed rough-in or final inspection on a remodel stalls the whole project. We correct the listed items and get the work ready to be looked at again.
You found a previous owner's wiring
Extension cords run through walls, mismatched wire sizes and outlets with reversed polarity are signs of unpermitted work worth checking.
Your insurer asked for repairs
Some insurers ask for specific electrical fixes after a home inspection. We handle the work and walk you through what was done.
What a Correction Job Looks Like
- 1
A phone call to go over it
Let us know what the report lists and any deadline you're facing. Then we set up a service visit that fits your schedule.
- 2
We check every item in person
We visit each flagged spot and confirm the real problem. Now and then an item is fine as installed, and we'll say so.
- 3
A clear scope and price for you
Before any work, you'll know which items we're fixing and the cost. We add nothing unless you agree.
- 4
The fixes get done
Only the circuits we're working on get shut off, floors in the work area are covered, and we clean up before heading out. One visit handles most lists.
- 5
Set for the reinspection
When a permit applies, we handle permits and inspections as the local jurisdiction requires. You also get a short summary of each fix to pass along to your inspector, buyer or agent.
What Sets the Price of Correction Work
We price correction work item by item from your list rather than as a set package. A handful of outlet swaps and cover plates runs far less than grounding or panel work. Once we've seen the job, the price matches your actual home.
- How many items, and what kind
- A visit covering ten quick fixes can come in under a single item that means running new wire through a finished wall.
- How easy the wiring is to reach
- An open garage goes faster than a cramped attic in the Texas summer or a wall that has to be opened up and patched afterward.
- Whether a permit is needed
- Certain corrections call for a permit and inspection, which bring fees and extra scheduling. Simple repairs often need neither.
- What turns up behind the item
- A bad outlet can be a clue to damaged wire farther along the circuit. When that happens, we pause and show you before doing more.
Your Questions About Correction Work
Something not covered here? (682) 841-6649
Does every item on the inspection report have to be fixed?
Not necessarily. In a sale, which repairs get done is usually worked out between you and the buyer. We point out which items affect safety and which are small, so your decision rests on clear facts.
Are you going to push a larger job on me?
No. The list is what we work on. If a serious hazard shows up that the report missed, we photograph it and explain it, and you make the call.
Is a permit needed for correction work?
Only when the work calls for it. We handle permits and inspections the way the local jurisdiction requires and let you know before we start whether your items need one.
How quickly can a report be cleared?
The electrical items from a typical home inspection usually wrap up in a single visit. Bigger items such as panel corrections or a rewired circuit take more time, plus any wait for an inspection.
Do you correct wiring a past owner installed on their own?
We do, and it's among the most frequent fixes we make. We bring the work up to code, and if a circuit can't be saved, we tell you why before it gets replaced.
Let's Get Your List Checked Off
Have your report or correction notice handy when you reach us. We'll talk through the items and set up a time to come out and fix them properly.